製品詳細
Wiki & 学習
レビュー
PDF をダウンロード

特長

  • The First STM32-Powered XIAO: Built with the STM32C5A3CG, featuring a 144MHz Arm Cortex-M33 processor, floating-point support, and DSP instructions for embedded control and sensor processing.
  • CAN FD Connectivity Built-In: Two native CAN FD interfaces, with one channel connected to an onboard TCAN3403-Q1 transceiver and accessible CANH/CANL pads. Add an external transceiver to use the second channel.
  • 6-Axis IMU with Programmable Heating: The onboard LSM6DS3TR-C accelerometer and gyroscope are paired with dedicated heating resistors around the sensor. GPIO-controlled heating enables programmable warm-up and, with temperature-feedback firmware, closed-loop temperature regulation to help reduce temperature-related drift in robotics and motion-sensing applications.
  • 16MB External Flash: Store application data, sensor logs, configuration files, and CAN message records using application firmware.
  • External Crystal for Communication Timing: An onboard high-speed external crystal provides a clock reference for CAN FD and other timing-sensitive applications.
  • USB-C and Battery Charging: Develop over USB-C or build battery-powered devices using the onboard lithium-battery charging circuit and battery connection pads.
  • Compact, Integration-Friendly Design: The XIAO form factor and castellated edge pads support breadboard prototyping with headers and integration into custom carrier boards.

仕様

ItemSpecification
Product Versions
ProductXIAO STM32C5
XIAO STM32C5 (Pre-Soldered)
Processor & Memory
MicrocontrollerSTMicroelectronics STM32C5A3CG
CPUSingle-core Arm Cortex-M33, up to 144 MHz, with FPU and DSP instructions
Internal program Flash1 MB
SRAM256 KB
External Flash16 MB
External clockOnboard 48 MHz HSE crystal with ±10 ppm initial frequency tolerance
CAN FD Connectivity
CAN Interface2 native FDCAN interfaces
Onboard CAN transceiver1 × TI TCAN3403-Q1
Onboard CAN bus connectionCANH/CANL pads; use board GND as the signal reference
Second CAN channelDigital TX/RX signals
External CAN transceiver required
CAN termination120 Ω, enabled by default
Disconnectable through a cuttable solder link
IMU & Temperature Control
IMUSTMicroelectronics LSM6DS3TR-C, 3-axis accelerometer and 3-axis gyroscope
IMU heatingDedicated heating resistors around the IMU with GPIO-controlled drive
Temperature regulationProgrammable warm-up
Closed-loop setpoint regulation requires temperature feedback and suitable application firmware
Interfaces & Power
USBUSB-C
USB 2.0 Full Speed, 12 Mbps signaling rate
Logic level3.3 V
PowerUSB-C 5 V input
Lithium battery through BAT pads
Battery chargingOnboard charging circuit
Debug interfaceSWD
Controls & Form Factor
User buttonReset button
Boot button
IndicatorsUser LED
Charging LED
Form factorCompact XIAO module with castellated edge pads

ハードウェア概要

用途

  • USB-to-CAN FD Development: Build a compact interface for CAN device testing, message exchange, and host-based analysis with suitable firmware and software.
  • CAN Sensor Nodes: Send motion measurements and data from external sensors over a wired CAN network.
  • Robot and Motion Controllers: Communicate with external CAN-enabled motor drives for robotics and motion-control prototypes.
  • Motion-Sensing and Stabilization Development: Explore IMU preheating and temperature regulation for robot startup routines, stabilization systems, and sensor-fusion experiments.
  • Embedded Data Logging: Record selected CAN traffic, IMU measurements, and application events in external Flash.
  • Portable Development Tools: Create battery-powered monitoring devices, test fixtures, and compact diagnostic prototypes.

認証

HSCODE8543709990
USHSCODE8517180050
UPC
EUHSCODE8543709099
COOCHINA

部品リスト

PartQuantity
XIAO STM32C51
2.54 mm 7-Pin Header2

Seeed Studio XIAO STM32C5

SKU 100036669

Meet the first STM32-powered XIAO. Built around the STM32C5A3CG with a 144MHz Arm Cortex-M33 core, XIAO STM32C5 brings CAN FD connectivity, 16MB of external Flash, and a six-axis IMU with programmable heating to the compact XIAO form factor. Dedicated heating resistors around the IMU enable firmware-controlled warm-up for robotics and motion-sensing projects. Two native CAN FD controllers, including one channel with an onboard TCAN3403-Q1 transceiver, provide a starting point for USB-to-CAN adapters, connected sensors, and robot control projects. USB-C and onboard battery charging support both desktop development and portable applications.

XIAO Dev Board
Pin Header
Package
JPY¥1567.00
Shipping and duties calculated at checkout.
  • Free Insurance Included On Us
  • Flexible Payments with PayPal Pay Later
  • Avoid Import Fees: Ship Tax-Free from Local Warehouses
  • 1 on 1 Support | 12-Month Warranty | 30-Day Return Policy